AED
AFN
ALL
AMD
ANG
AOA
ARS
AUD
AWG
AZN
BAM
BBD
BDT
BGN
BHD
BIF
BMD
BND
BOB
BRL
BSD
BTN
BWP
BYN
BZD
CAD
CDF
CHF
CLF
CLP
CNH
CNY
COP
CRC
CUC
CUP
CVE
CZK
DJF
DKK
DOP
DZD
EGP
ERN
ETB
EUR
FJD
FKP
GEL
GGP
GHS
GIP
GMD
GNF
GTQ
GYD
HKD
HNL
HRK
HTG
HUF
IDR
ILS
IMP
INR
IQD
IRR
ISK
JEP
JMD
JOD
JPY
KES
KGS
KHR
KMF
KPW
KRW
KWD
KYD
KZT
LAK
LBP
LKR
LRD
LSL
LYD
MAD
MDL
MGA
MKD
MMK
MNT
MOP
MRU
MUR
MVR
MWK
MXN
MYR
MZN
NAD
NGN
NIO
NOK
NPR
NZD
OMR
PAB
PEN
PGK
PHP
PKR
PLN
PYG
QAR
RON
RSD
RUB
RWF
SAR
SBD
SCR
SDG
SEK
SGD
SHP
SLE
SLL
SOS
SRD
SSP
STD
STN
SVC
SYP
SZL
THB
TJS
TMT
TND
TOP
TRY
TTD
TWD
TZS
UAH
UGX
USD
UYU
UZS
VES
VND
VUV
WST
XAF
XCD
XCG
XOF
XPF
YER
ZAR
ZMW
ZWG
ZWL
Carboline Thermaline 440 10L Kit
Carboline Thermaline 440 10L Kit
Thermaline 440 (formerly Thermaline 400 EU) is a high performance, heat resistant epoxy phenolic that specializes in providing color for uninsulated piping and equipment. This immersion-grade coating which has excellent resistance to wet/dry cycling conditions at elevated temperatures when using dry grind pigments. This formulation allows for use on hot steel substrates under insulation operating continuously up to 400°F (204°C). It has excellent chemical resistance properties to handle the corrosive effects of wet insulation under thermal cycling conditions.
Product Features
- Versatile use from cryogenic temperatures of -320°F (-196°C) up to 400°F (204ºC) exposures
- Very good flexibility
- Excellent overall chemical resistance
- Very good abrasion resistance
- Easily applied by spray
- Acceptable for use over stainless steels
- Rapid Tint System Colors available*
| Color | A wide range of colors is available upon request using Carboline’s Rapid Tint System (RTS). Contact your Carboline representative for RTS color availability. Rapid tint colors are not recommended for CUI and/or immersion service. Coating discoloration can be expected when exposed to elevated temperatures in excess of 200°F (93°C). This discoloration does not affect performance. |
| Finish | Semi-Gloss |
| Dry Film Thickness | 5 - 6 mils (127 - 152 microns) per coat Dry film thickness above 10 mils (250 microns) per coat, is not recommended. |
| Solid(s) Content | Solids by volume: 52 ± 2% |
| Theoretical Coverage Rates |
166 sq.ft/gallon at 5.0 mils DFT (4.0 sq.m/liter at 125 µm) 139 sq.ft/gallon at 6.0 mils DFT (3.4 sq.m/liter at 150 µm) Mixing and application losses will vary and must be taken into consideration when estimating project requirements. |
| VOC Values | As Supplied : 3.50 lbs/gal (420 g/l) Thinner 236 E : 3.50 lbs/gal (420 g/l) Thinner 2 : 3.68 lbs/gal (441 g/l) Thinner 33 : 3.69 lbs/gal (443 g/l) The use of Thinner 2 or Thinner 33 may exceed your local allowances for VOC. Please check your local regulations before using. Thinner 236 E is a US EPA VOC exempt solvent |
| Under Insulation Resistance |
Continuous: 400°F (204°C) Non-Continuous: 450°F (232°C) |
| Limitations | Discoloration will occur when exposed to temperatures in excess of 200°F (93°C), however product will perform as intended. Not recommended for exposure to strong mineral or organic acids. For CUI & immersion projects use only factory made material in special colors. Epoxies may lose gloss, discolor and eventually chalk in sunlight exposure. |
| General | Surfaces must be clean and dry. All surfaces must be thoroughly cleaned to remove dirt, grease, and any other contaminants that can reduce adhesion per SSPC-SP1 solvent cleaning with recommended surface preparation. |
| Steel | Abrasive blast to SSPC-SP10 (ISO 8501-1 Sa 2½) to obtain a 1.5 - 3.0 mil (35 - 75 µm) anchor profile. For previously prepared substrates that have an existing anchor profile, High Pressure Water Jetting (HPWJ) to a minimum WJ-1 standard is acceptable. |
| Stainless Steel | Surface profile should be a dense angular 1.0 - 2.0 (25 - 50 µm) mils and is best achieved through abrasive blasting (non-metallic abrasive)per SSPC-SP16. Remove all contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, embedded iron or chlorides. |
Data Sheets
Thermaline 440 PDS
Thermaline 440 SDS Part A
Thermalinr 440 SDS Part B
Product Flyer - Thermaline 440
The above information is based on current test data, health and safety information and application instructions supplied by our suppliers and manufacturers of the products. It is supplied for guidance and to the best of our knowledge is true and accurate. Customers should satisfy themselves to the suitability of the products in its intended use and no guarantee is given or implied as the conditions of actual use are beyond our control. If in doubt the customer should consult the designer of the project or the local building control.
Fire Stopping Shop, disclaim any liability for loss, damage or other expense which may arise from the use of this information, data or products refereed to and reserve the right to amend or change any details without notice. This statement does not affect your statuary rights.
